IVAR Shut-off valves

Pair of angular male-female ball valves with soft seal fitting, butterfly. Includes supply and return...

Pair of angular male-male ball valves with soft seal fitting and thermometer, butterfly operation. Includes supply and return...

Automatic air vent valve allows the bleeding of air contained within the liquid stream, thuspreventing problems of noise, performance drops due to air pockets, and metallic componentcorrosion phenomena. This operation is particularly important during plant filling and pressurising phases, but it is crucial also during normal operation, when small air pockets can betrapped within the piping system...

Automatic filling groups are used to supply water to closed-loop heating systems and are able to stabilize the pressure in the heating system and, if necessary, recharge the water in the circuit. When the operating pressure in the system is reached, the feed unit closes automatically. IVAR supply units operate with an inlet pressure of more than 16 bar and offer an outlet pressure adjustment range..

Balancing valves allow the creation of appropriate differential pressures to ensure that each branch of the hydraulic circuit has the required design flow. They are installed at the ends of a calibrated orifice using a special kit (AVB 20), and determine the differential pressure Δp, which is directly related to the flow through the valve...

The CombiMix is ​​a mixing and booster unit for radiant systems. The supply temperature is controlled by a two-way valve that regulates the hot water supply to the mixer ("injection" system).The device is available in a fixed point version with a thermostatic head or in a temperature controlled version with a servomotor, which can be supplemented with an electronic controller with an external sens..

Electrothermal head normally closed (2 wires). Suitable for all IVAR thermostatic inserts and manifolds with a center distance ≥ 40 mm (without EASY-RADIANT)...

Electrothermal head normally closed (2 wires). Suitable for all IVAR thermostatic inserts and manifolds with a center distance ≥ 50 mm (without EASY-RADIANT)...

Temperature range: 0÷90 ◦CDifferential: ∆T = 2 ÷ 5 KMax. box temperature: 90 ◦CRated current and voltage: C-1 16(3)A/250V∼; C-26(1)A/250V∼..

Nipple connector for manifolds 1 "(inch)..

DirtSTOP® XL is the new high performance magnetic dirt separator from IVAR with triple filter action.1. Vortex motion, contributing to the deposition of waste2. Powerful magnet (14000 gauss)3. Mesh cartridge for separating smaller particles.A special patented inner insert directs the flow into the vortex to facilitate cyclonic separation of waste, prior to magnetic and mechanical deformation.This ..

Retaining elbow to protect the pipe...

1 "pressure reducer for cold and hot water supply systems with a mesh filter (1.5-6 bar).Pressure reducing valves are widely used in private installations to separate the system from public water lines, which are characterized by too high and variable pressure for direct use in domestic installations. In fact, the pressure reducing valve is able to reduce and stabilize the outlet pressure even wit..

Manual valves are radiator shut-off devices that operate entirely by hand.The DRM series also performs a double micrometric adjustment of the opening setting, memorizing it in the event of subsequent trips...

The thermostatic valve is a device that regulates the flow of water to the radiator and adjusts to a thermostatic command. The adjusting rod ring nut can be replaced and checked while the system is running. IVAR valves in all figures are supplied with a protective cap instead of a regulator or with a manual head. The pipe connection can be internal or external, and for connection to the radiator y..

In addition to the inlet valve to the radiator, a gate valve with locking and regulation functions should be installed at the outlet.IVAR regulating valve is offered in a standard version (series 300) or as a twin of the corresponding inlet valve, also in coaxial figures (series 200). In both cases, the pipe connection can be internal or external, and the radiator connection can be a standard coni..

The set includes: feed, return, thermal head.Radiator components are included in a pre-configured kit for standard requirements. Each kit includes a thermostatic valve (valve + actuator) and a shut-off screen.The valve can be standard or pre-regulated. Radiator connections and piping can be selected with the same options as volumetric components...

The thermostatic valve is a device that regulates the flow of water to the radiator and adjusts to a thermostatic command. The adjusting rod ring nut can be replaced and checked while the system is running. IVAR valves in all figures are supplied with a protective cap instead of a regulator or with a manual head. The pipe connection can be internal or external, and for connection to the radiator y..

    IVAR's piping offer is more complete than ever, with the ability to meet any system requirement for both domestic hot water and heating / air conditioning applications.The offer is divided into three main categories of pipes:• Multilayer, available in PE-Xb / Al / PE-Xb rods (made in Germany) or in coils PE-Xb / Al / PE-HD (made in Germany) or PE-Xb / Al / PE-Xb (made in It..

Electric motor for rotor mixing valves. All-brass rotor mixing valves offer the advantage of an extremely low risk of rotor-body connection, while being significantly smaller and lighter than equivalent cast iron components...

    Unbearable Outlets: When you turn one of the two manifolds 180 °, you get the outlets misaligned. This feature makes pipe installation very easy.IVAR steel manifolds are a valid alternative to traditional brass manifolds. They are used to distribute the heating medium in both radiant panel systems and radiators, and are also compatible with cooling systems where suitable in..

Pair of straight male-female ball valves with soft seal fitting, butterfly. Includes supply and return...

Pair of straight male-male ball valves with soft seal fitting and thermometer, butterfly operation. Includes supply and return...

Thermostatic mixing valves with side mixer. The valves in this section are piston mixers controlled by a thermostatic actuator, equipped with a remote sensor or motorized for modulating control by motors or electrothermal actuators...

Thermostatic heads are mechanical devices for automatically regulating the flow of water to the radiator thanks to a temperature-sensitive element that reacts to fluctuations in ambient temperature. Available in liquid form and with a remote sensor in case of obstacles in front of the radiator.More than 180 models of IVAR thermostatic valves carry the Keymark EN 215 marking, which certifies a syst..

Thermostatic heads are mechanical devices for automatically regulating the flow of water to the radiator thanks to a temperature-sensitive element that reacts to fluctuations in ambient temperature. Available in liquid form and with a remote sensor in case of obstacles in front of the radiator.More than 180 models of IVAR thermostatic valves carry the Keymark EN 215 marking, which certifies a syst..

    ONE SINGLE FITTING FOR TWO TYPES OF PIPE:• Multilayer pipe • PEX pipe..

Rotary mixing valves are used in heating and cooling systems for the typical purpose of mixing and distributing liquid. The overall stroke is achieved by turning the rotor 90 °. The valves can be operated manually or automatically by installing a servomotor controlled in turn by a thermostat or climate controller. The 3-way valves can be used as mixing or switching devices (for example as priority..